Search results

of course it is a resin :) which type though? VinylEster or Polyester? :)

No damage Just remember to fill it up with diff oil after you install it again :)

yikes I am not a big fan of hummus. Avacado is TASTY but damn its mud butt properties!

I will tell you straight up. Why not be honest from the get go? Why say " I will ship Monday" and then monday comes and goes and nothing. Communication is ALWAYS what seperates a good seller from a not so good a seller.

You are aware that the stock cams are ALSO hollow right? How do you think oil lubrication gets to the bearings? ;)

juan first off. Good luck. As you noticed. Everyone wants things on the cheap for this type of stuff. I know the cost and it won't be anywhere near that but leave it to the dreamers, hopefull and low ballers! #2. What will the material be? CF3k, CF6k, CF12k, Kev/CF? #3. Twill? 2x2, 4x4...

only one way to do it if there is no information for it. Open the diff and count the teeth on the pinion and ring divide the ring teeth by the pinion teeth to get the ratio. Also note the center section. Non-lsd should be almost empty and LSD should be really really cluttered.

PM sent but in short.... If you look at the arm where it connects to the flapper door lever. You will see that it is held in place by a removable pin. Well if you continue to the rod you will see that it is threaded. Lengthen rod and you lower the psi the waste gate will open at ;)

Well, In airplanes around the world. Lots of wire bundles are niether heat shrinked or nylon-tie wrapped so do not dispair. Instead they use a lacing technique to bundle the wires together which allows air to still circulate around the wire harness/bundle while keeping the bundle nice and tidy...

well the way the aerospace industry bundles is quite odd when you look at it but then take into consideration the other part and it makes perfect sense :) We call it lacing. Works quiet well in keeping the bundle together tight but allows for air movement over the said bundle :) I...

well I will give you MY experience as things sit today. :) MoTeC PDM32 = $5000 by itself M22759/91 wiring for all 32 outputs, 23 inputs, CANBus and 4 Gauge input. $1000. Some money can be saved here if going with basic tefzel (M22759/16) or the lightweight (M22759/18/ wire). Autosport...

umm you are VERY aware that from factory (greddy) the td06 is set at 15 psi BUT that it can be adjusted to anything below that right? I had my turbo adjusted to 9 psi ;) btw running at 11 psi will more than likely cause fuel cut if the temprature/barameter are low enough.

well quite simple really look at the rubber portion. If it looks cracked and falling apart. That means that the entire rubber portion is cracked and brittle. In other words it is not dampening anything. On a 87 supra. That will make the pulley 21 years and counting. Too old to be worth...

ahh ok well you can do what the newer 89-92 supras did. Put a pusher fan infront of the A/C condensor. This one came on with the A/C and not the two tiny ones on the side. Even though they are small, those fan are actually quite the air movers and would be ideal to be controlled by the A/C :)

Electric fans to replace the mechanical fans? My advise. Don't. Keep the mechanical fan. Electricals will never ever ever pull as much air as the stock mechanical setup. Especially the hokie Fal 330/340 which are really not that powerful. If electrical fans are what you want, go with the...

12 psi on a td06-20g? try cranking the boost up to 17 psi on that turbo. World of a difference! btw. Isn't your head messed up?

not really. You will get quick readings for boost, fuel pressure, boost controller almost at the same time. Keep the lines small since it is for pressure and not volume readings ;)

In true Baron Cohen genius.... the website for the fights is registered under Peto Philer yes. He is that bold. lol

105 octane avg.

being dupped for the second time! http://www2.arkansasonline.com/news/2008/jul/07/fake-fighting-draws-crowds/ Cliffs: Beer was $1 Fight was scheduled for two cage "fighters". "fighters" came in, stripped each other down to underwear/knickers. "fighter" began kissing and touching...