Search results

Well I did some research and it seems that it should be set 10 degrees. Correct me if I'm wrong cause I'm no expert in this area. It will depend on how big the turbo, at what psi I plan on running, and elevation as to whether or not I can advance timing. So with turbo that I'm running and only...

List of mods- 60-1 Cxracing spearco replica Rc 550's Walbro 255 FP Aero fpr Map-ecu Spec stage 3 clutch 1 piece drive shaft arp head studs oem gasket (purchased the car like this) Stock bottom end So got a call today from the shop that is tuning my car. He ask me how much boost was I...

That is a good question. I'm a noobie when it comes to engines. So unsure of what you mean. But I guess that's why I'm on the forum to learn.

IJ I have discovered That 1,2,4,6 on the exhaust side are leaking and 6 was leaking bad. More of a flow then a leak. But on the intake side there were no leaks at all.

Ok thanks I will see what I can find.

Sounds like a plan. This will take a while because funds are tight right now but if you want it done right you have to spend the money. Thanks for the advice guys. ---------- Post added at 02:49 PM ---------- Previous post was at 02:43 PM ---------- IJ this might seem like a dum question but I...

Airhead I totally agree with you. I knew that something wasn't right when he came done to $600. Granted I knew something wasn't right when I saw those compression numbers. I knew by buying this engine that it could possibly be a parts engine. But I thought that the parts were worth a least...

How do you know the rings are shot? Not 100% positive. I'm having a friend take a look at them. Why did the guy sell the engine in the first place? Guy was doing a 2j swap and needed funds. Pics of said pistons and cylinder walls? Will work on pics having problems uploading them. Was there...

So no one can give me some helpful advice.

I recently purchased a 7m with forged internals. He was asking 1500 for the engine and I offered him 1200 for it and I would come and pick it up. JE pistons, eagle rods, clevite 77 race bearings, arp components, claimed to of had new crank, new head (port and polished), new cams, metal head...

That helps. So you think with stock suspension set up it will rub. I have the stock saw blades on right now with 225/50/16 and when fully turned there is about 2 inches from the tire to the spring. Granted your not driving so there is no way to really know how close you get.

Will 245/45 work up front or will they rub with tt wheels without spacers

Can I go 245/45/r17 for the front on mkiv tt wheel without spacers and not rub. Or should I go 235/45/r17 for the fronts.

Black 88 pics http://viewmorepics.myspace.com/index.cfm?fuseaction=user.editAlbumPhoto&albumID=1527334&imageID=23711679 http://viewmorepics.myspace.com/index.cfm?fuseaction=user.editAlbumPhoto&albumID=1527334&imageID=23711682...

Also tracked all vacuum lines and they appear to be hooked up correctly. Went back and unbolted the fuse box and ignitor and discounted the two grounds under those two things. Cleaned up both grounds and grinded off the paint where it was bolted to get a good connection. I have checked fuses...

No after messing with the stuff under the hood I started it and it was fine other then idling high at cold start. Messed with tune it start acting up on me idling at 450rpm. Reloaded the original map the one that it ran fine on before I messed with it and I got the same result idling at 450rpm.

Sorry for such a long post. I had to be detailed of everything that I did to answer any questions that might of been asked. Thanks So recently decided that my engine bay needed a cleaning. I started with just unbolting some electrical components (ignitor, fuse box etc..). Removed horn, cruise...

It is uego 1000

Anybody had this problem or know how to help. thanks

I have connected the wideband output of the uego to the yellow wire of the mapecu and the ground to one of the grounds of the mapecu. Have selected the AEM.o2 under mapcal configurations and all the mapecu is saying is rich it is not giving an actual AFR reading. I have followed the install...