Search results

Finally was able to finish up my 1jz swap into a SC300. For some reason at idle its misfiring sounds bad. This is on stock downpipe, stock cat, stock exhaust. Stock turbos no tune, no fuel upgrade. Walbro fuel pump installed. Idle is kind of low maybe 600. Even when I raise the idle up a...

Got it started today!!!!!! I tore apart the timing and saw that the crank gear was not on all the way with the flat gear in the back where it would work with the crank sensor. Pulled the gear off and put the two pieces together, put the timing belt back. Fired right up. Finally figured it out...

Search around forums, usually people sell their 1jz wiring harness. Also check ebay, I believe there is a 1jz harness and a couple of ecu on ebay right now.

The 0 mark on the timing belt cover on the block? That is suppose to be the mark for the harmonic balancer to be align to right? What about the cam gears? I used the white marking on the cam gear and have it align to the marks on the back plate of the cam gear on the top.

All I did was fix the tach and temp gauge. Basicl add a ground for the temp gauge. Also I fixed the wires for the CEL to be able to turn on. Which was just switch a wire over on the JDM connecter. I can definitely smell fuel from the spark plugs. Still no spark. Code 12, RPM signal...

I'm getting 12v to the coil wires, Injecters are fine, I can smell the fuel on the spark plugs. So there seem to be fuel going in. I can hear the main relay turning on and off. RPM signal, usually mean crankshaft or camshaft position doesn't it? Anyone have a picture of how the timing mark...

1jzgte swap into a sc300. 1jzgte is from a soarer. I got no spark, igniter is fine. I got a check engine code 12. I have no idea what the code is. Anyone know?

I'm getting a code 12 now. Getting fuel, still no spark.

I'm thinking it may be the ECU. Its a ecu from a soarer. I also have another one from a chaser, should be able to work fine. Tried with both ECU, still nothing. I'm also looking at the 1B+ and the B+ wire that is suppose to get voltage, I'm not getting voltage, when I do splice a 12v souce into...

I did a check engine light today to bring up the code. I would get non stop blinks. Would that be a code 0? It wasn't the regular blink you would see and count the blinks as codes.

I've tried splicing a 12v source to the +B1 and +B, still nothing. Cranks fine doesn't start. Checked all the fuses again. Nothing. ECU looks fine.

Constant 12v has no voltage what so ever. Even with key on. Wire BATT has voltage even with no key and with key on and the other wire is fine with the key on, no voltage with the key off. Basicly no voltage at the +B1 and +B with key or no key.

Fuses are all fine.

Hi guys, I'm finishing up a 1jz swap into a sc300. Anyways, about a week ago I finished. Went to try and start it nothing. Turns out no spark and no fuel. Since then Ive tried 2 different ECU. I checked the crank sensor and cam sensors which were all good. I'm getting voltage to the...

I got a 1jz wiring harness that seem to be cut at the body plugs and fusebox. Its from I believe a jzz30. Its what I ordered but who knows. I know forsure its not from a supra. Anyways its going into my sc300. My question is, will I be able to use the body plugs off the sc300 2jz motor and...

I'm not sure I want to take that risk. If I ever decide to I'll post up how it goes.

I just got an email back from Sean today. They don't have any stock piston rings.... :cry:

disregard this post. lol

Thats freaking awesome. Post up some pictures of shifter and hows the tranny/engine mounted. Looks good.

Does Titan sell the 1jz piston rings alone or do they sell them with the pistons itself as a set? I'm also in desperate need of piston rings.