Tookwik's 7M-GTE COP ignition mod w/ stock electronics...pics and writeup
- Thread starter tookwik4u89
- Start date
cheefer60;1284217 said:
90980-11246....the other #'s for the PIN's are further back in the thread.
cheefer60;1286210 said:
no, the gte pigtail has 3. the 1/6 connector will reach the coil on #1. the other 2, have to be extended to reach the 2/5 & 3/4.
everything you need to know is on the 1st page or 2 of this thread!!!
Can anyone tell me the wire color for an 88 coil harness? I chopped mine apart to extend the wires, and have now stupidly forgotten which wire goes to which coil. Obviously there is a common wire (tan on my harness), so I need to know which coil the other wires go to. I looked though the TSRM and couldn't find it, unless theres somewhere else to look in there?
Also, I looked on here: http://www.cygnusx1.net/Supra/Library/TEWD/MK3/manual.aspx?S=Main&P=040 and it shows wire colors, but this is for an 89, so my 88 would be different.
Also, I looked on here: http://www.cygnusx1.net/Supra/Library/TEWD/MK3/manual.aspx?S=Main&P=040 and it shows wire colors, but this is for an 89, so my 88 would be different.
figured it out. looking at the coil harness (not the wiring harness):
(Clip)
[G][T]
[W]
[T]=tan, which is the common wire
coil for 1,6: [T]
coil for 3,4: [G][T]
coil for 2,5: [W][T]
Also, if you want to build a new harness, check this out (reposted from a thread in the electrical section): http://easternbeaver.com/Main/Elec__Products/Connectors/Waterproof_Connectors/SM-MT/sm-mt.html
It looks like the 4P090WP-MT is the same as the stock coil harness connector, but double check for yourself (ie, don't blame me if you buy it and it doesn't fit).
(Clip)
[G][T]
[W]
[T]=tan, which is the common wire
coil for 1,6: [T]
coil for 3,4: [G][T]
coil for 2,5: [W][T]
Also, if you want to build a new harness, check this out (reposted from a thread in the electrical section): http://easternbeaver.com/Main/Elec__Products/Connectors/Waterproof_Connectors/SM-MT/sm-mt.html
It looks like the 4P090WP-MT is the same as the stock coil harness connector, but double check for yourself (ie, don't blame me if you buy it and it doesn't fit).
Wondering if these would work? AEM CDI PENCIL COILS I saw an add for them in a car mag.
http://www.aempower.com/ViewCategory.aspx?CategoryID=352
I did a search and did not find anyone that asked this yet.
http://www.aempower.com/ViewCategory.aspx?CategoryID=352
I did a search and did not find anyone that asked this yet.
doubt they would work with the stock ecu, but would probably work if you run an aftermarket ecu
just did the conversion and fired up like a champ...with the old 7m coils it took forever to start
this might have been stated earlyer but on the wiring note do you have to wire the new coils and diffrent the the stock ones. esentialy all you are doing is extending the wiring harness to fit the new coils
sorry in advance if this was all ready answered jut got my car back and iv been in the fourms for a few hour reading and i dont feel like reading this treads ever post
sorry in advance if this was all ready answered jut got my car back and iv been in the fourms for a few hour reading and i dont feel like reading this treads ever post
