Search results

Do you know how to test 3 wires? I found this, but i'm not sure i'm testing this correctly. I'm getting 11.xx Volts from wire #2 to ground... If i'm doing this correctly, then this is probably where my problem is. I'm just unsure about where to look to narrow down the source of the problem...

I'm having a similar problem and I think my engine is frying the alternators (1 old and 2 new) i'm installing... Is there a way to check proper functioning of the 3 wires in the plug that go into the alternator. Did OP ever fix his problem?

The 0 is for initial calibration... The 10 and 15 are for use with the timing light after you get it running, warmed up, and idled...

If you are following the TSRM, make sure you turn counterclockwise and clockwise when specified... I had a FAIL experience because I would read counterclockwise as clockwise so I was always 180 degrees off... :P Drove me nuts lol... Also do the CPS exactly as the TSRM says... :) Are...

No, that's not possible... When the cam gears were put back on, was the pin properly reinstalled into the middle hole? Important!!! I know there's no Code 15... Maybe your ECU is toast... :( Hope not... But if you get an unexpected code, reset the ECU and try again...

Disconnect the negative from the battery for a minute to clear any codes and then check again...

http://www.cygnusx1.net/Supra/Library/TSRM/MK3/manual.aspx?Section=AT&P=9 This site is your bible... ^ ^ Check it out...

Vacuum Piping Diagram v v http://www.cygnusx1.net/Supra/Library/EPC/291420/catalog.aspx?F=1708&P=3 Picture may help too... http://upload.wikimedia.org/wikipedia/commons/1/13/7M-GTE_side_view.jpg You should be able to plug them in without taking it off, but it will be a pain in the ass...

Read the link and follow exactly as it says... http://www.cygnusx1.net/Supra/Library/TSRM/MK3/manual.aspx?S=IG&P=21 I don't have the 7mgte, I have the 7mge... Based on the TSRM I don't believe you have to remove the intake manifold. I think it's just the power steering reservoir and a few...

YES CHECK THE CPS via http://www.cygnusx1.net/Supra/Library/TSRM/MK3/manual.aspx?S=IG&P=24

My guess first off would be that you don't have spark or spark at the right time. Step one: Check CPS. (This has always been my stupid downfall after rebuilds, only I have an 7MGE. <----------DO THIS FIRST http://www.cygnusx1.net/Supra/Library/TSRM/MK3/manual.aspx?Section=IG&P=21 Step two...

Sorry about the wrong info... My bad... you're right... IDK why I put an o-ring on my distributor but I took it off and it fixed everything... The TSRM even says the replace the o-ring. So i replaced it with one from toyota... Oh well... Runs great now!!! Thanks to all... :) SUPRAWR

ALSO: the Resistance on my Injectors was about 44ohms @ 70 degrees F (TSRM says they should be at 38ohms.) Could this be a major problem?

Like too much pressure? Or too little? Also, by taking the EFI fuse out i will not get spark, so how would the extra fuel burn up? It may be pushed out by the exhaust, but not burned up. Do you think it's a clogged/pinched that is causing this?

I have a distributor, but yes i checked it and set it up according to the TSRM. If i had a ground problem to the coils wouldn't I not get spark and wouldn't i get no ignition at all?

I just replaced the crank, piston rings, bearings, head gasket, and spark plugs in my 7mge. I'm having trouble getting it started. It turns over. I have done all of the following: Put it in time according to the TSRM. Checked compression in 1 and 2. 160psi Good Checked spark on all...

jdub, I'm going to buy oil tomorrow morning and I was wondering how much and of what kind you would recommend since I just replaced the crank and piston rings in my bone stock 7mge. I have not added any oil yet and was wondering how long I should wait until i do my first change? BTW I live in...

hello all!!! My friend Brandy is in a hottie of the month contest and would like to ask all of you to take 10 seconds out of your night and Vote for my good friend Brandy for the Space Coast Hottie of the Month. Remember Brandy Lynn PS: Check out her bikini pics ;-)

Sears didn't have a thin-wall, so i got a regular 14mm 12pt 1/2" and it was too big w/o removing the cams... :( Anyone know where else i can get a thin-wall 14mm 12pt 1/2"?

Thanks to both of you... Heading to Sears now.