Search results

Hi Kenny, Have you checked your plug wires for resistance, or in my 7M's case plug wires #1 & 6 were oil soaked from a leak around the valve cover gasket, into the the valley. After I cleaned the oil off the plugs, wires and valley with break clean, the misfire went away. HTH Van

You're welcome.

I went to Forged Performance and spoke to Jon, (their tuner), here is how he answered the questions: 1.) Once the cams have been tuned, timing needs to be "re-sync'd" Yes. Adjust the CPS and re time the ignition as usual on our car 2.) GREAT care must be taken when adjusting the exhaust...

This Friday AM, in fact.

I suspect you're right... That our 7Ms (using cam sensor VS crank sensor), are a different kettle of fish.:dunno: The place I'm headed to for Dyno tuning, Forged Performance, tunes our 7Ms and JZs. Van

As regards the timing resync'd recommendation: This is a very good topic for me, as I'm getting ready to get the 7M tuned using adjustable cam gears... The following is taken from Hondata.com (w/o permission) and is information given to tuners working on a dyno tune. "Before the cam timing is...

Hi Jet Jock, Well... Better late than never! Sure 'nuf, there it is in the TSRM, Code 32, GE only. That said, how do I resolve this problem code on a GTE? The ISCV is now working, it had a bad connection thanks to piece of paper towel in the connector that got there after I "cleaned it". I...

Now the culprit has come out of the wood work... The ISC stopped working yesterday (no clicking sounds). That code 32 may have been thrown as the ISC was having intermittent malfunction. I'll bench test it Saturday, to see what's wrong. I may be in the market for a rebuilt one, as new is $529...

It's time to revive this thread... Yes, the torque plate is available for rent. Rental policy for the 7M Tq Plate: Deposit $355, in addition to your choice of shipping and insurance on the torque plate, shipped through the US Postal Service (Tq plate is valued at $355). When the Tq plate is...

A little motivation, can go a long way...

I'm thinking of a policy change to require a deposit into PayPal... I remember that there is a Ron R 7M torque plate out there, somewhere. I recall that what is required is paying the cost of shipping. That plate is still out there, not readily available though, that is why I bought one. What...

3P, Thanks for the feed back. Van

Today, I installed the ND 2JZGTE fuel pump. I'm keeping the two step voltage to the fuel pump (on a fully built 7MGTE). Will that be problematic? I'm running ND 550cc injectors, Lex AFM w/ adj screw, stock TCCS, new fuel pressure relay, regulator and damper. Blitz Dual SBC type R, 50 trim CT26...

The 7M torque plate is again, available to rent. Van

Sam, I tried yesterday to mail/ship out the plate, insured, then both USPS & UPS told me I will need to repack as it won't ship as I packed it (I tried to ship using light weight cardboard). I've heavier weight cardboard I can get my hands on and I will ship on Monday. It's going ground so it...

I'll ship the plate tomorrow, the 23rd, as today is my 26th wedding anniversary. Van

Sam, I'll be able to go to the UPS Store this week. Give me your shipping info and PayPal me the $26. I'll send it out and give you a heads-up and tracking number too, if needed. Van

The ISC is within spec per TSRM. I cleaned it up as well as checked its functionality, per TSRM. This afternoon, I adjusted the throttle body stop screw for the throttle plate and was able to set the ignition timing per TSRM. It now idles at 750 RPM and advance is 10-12 degrees, with paper clip...

Cold Vac is 19.7. Rev to 4000 RPM and snap the throttle closed, raises Vac to 25-26in/Hg. I'll be making a run to the store and will recheck the Vac numbers afterward. Van Hot Vac is 20, snap throttle closed it rises just above 25in/Hg. There is a hesitation from off IDL and the Vac drops to...

Good Day Sam, I'm in the process of deciding if my current policy of lending the plate, is wise. A fellow forum member brought up the caveat that a deposit for the full value of the plate would help motivate others returning the plate, otherwise, it may not return. A suggestion is to hold an...