Search results

  1. I

    jdmfreak's A NEW BEGINNING (BUILD THREAD)

    If you go too high the Coil will overheat split it's case and spew Epoxy and goo everywhere.... There are very specific requirements for dwell, 4ms across the board isn't it... Do you have a table for voltage/rpm?
  2. I

    For ~450whp what type of exhaust housing would you guys recommend?

    .63 will likely choke long before 450...
  3. I

    Ridiculous 1000HP 7M Street MK3 Build

    LOL nice save! :)
  4. I

    Dropped a valve on garage floor

    Put it in a drill chuck and spin it up to see if it's still straight..
  5. I

    My quest for 500whp under 2500 bucks

    Yep Teflon will be fine at those temps and being a single layer material it's ok to submerse.
  6. I

    Ridiculous 1000HP 7M Street MK3 Build

    LOL I never had any luck welding on the stock covers no matter what I tried..... Always warped even when bolted down..
  7. I

    jdmfreak's A NEW BEGINNING (BUILD THREAD)

    Can't really think of anywhere with easy access....
  8. I

    Ridiculous 1000HP 7M Street MK3 Build

    How flat are the covers after that?
  9. I

    jdmfreak's A NEW BEGINNING (BUILD THREAD)

    Gets pretty hot under there when running...
  10. I

    My quest for 500whp under 2500 bucks

    Just put a factory hardline back in there....
  11. I

    My quest for 500whp under 2500 bucks

  12. I

    My quest for 500whp under 2500 bucks

    We all have a piece of special submersible Hose in our fuel tanks (@ something like $200 per metre) put normal hose in there wait a couple of weeks and see what you end up with... As for how long it will live in Oil ask NoseChunks/Dan how long his lasted he could answer better than I can as...
  13. I

    My quest for 500whp under 2500 bucks

    Yeah ok..... :nono: Plenty of High Hp 7M's getting around with the stock hardpipe and no issues at all.. If you want to spend the $ fine but don't think you're fixing an inherent problem. The Softline kits on the other hand are a joke plain and simple.
  14. I

    My quest for 500whp under 2500 bucks

    Pet peeve of mine ;) Dunno is it Rubber inside? The outer layer of rubber hose isn't meant to be submersed and softens in time, the AN fittings "lock" onto the outside of the hose so when the rubber softens they fail... There is 0 reason to replace the stock hardline..
  15. I

    My quest for 500whp under 2500 bucks

    Unless that Braided line on the Oil Pump is a Teflon line I'd get it out of there before it fails.... :nono:
  16. I

    jdmfreak's A NEW BEGINNING (BUILD THREAD)

    LSx is there anything you can't do ;)
  17. I

    New 280z guy here

    Coupe or +2? Hard to tell from the angle of the pic, we didn't get the 280 Coupes here :(
  18. I

    Im in a real pickle

    What's the lash set at? The Shims do actually rotate while it's running.
  19. I

    Im in a real pickle

    Is that on the heel of every Lobe?
  20. I

    Im in a real pickle

    As I said I personally wouldn't run it again... Trailer it, you might get away with a cheap freshen up and then you can sell it and recover some costs, drive it more and you run the risk of kicking a leg out... and it being scrap..
Top Bottom