Search results

my plan was to build a decent block that i felt could withstnd a fair amount of power, and then research wich ems and turbo would work best for me, my goal is to get into the 800hp range with out sacraficing spool time. what turbo should i be looking at to have full boost/spool by 4300 rpm or...

my mods so far consist of. 1. crower forged connectiong rods. custom spec 2. forged wiseco pistons. custom spec. 3. forged crankshaft. custom spec. 4. clevitte 77 rod bearings. 5. ARP hardware on entire motor. 6. tms main caps 7. clevitte 77 thrust washers 8. block bored 3.2L + decked...

GT 42. Turb. Hous. A/R 1.22, Divided, 6 Bolt, Comp. Hous. A/R .6 [805138] $690.00 GT 42. Turb. Hous. A/R 1.22, Divided, 6 Bolt, Comp. Hous. A/R .6 Click to enlarge Turbine Wheel Compressor Wheel Exducer diameter Mayor diameter Exducer diameter Mayor diameter 2.67" 3.22" 2.63" 3.89"...

nice to know your a masshole as well ,now that you mention it that procedure does sound very compex, can u get me a picture to help me find the Cars Power steering (cps) and which ger should i be spining in ? no seriously thanks for the tip im sure it will make it alot easier sence im...

wear exactly is the ecu groung on the intake? i performed a check on the cps today and found that it is defective. tomorrow will instal new cps nd try for spark. are u saying chck for spark by spinning the cps by hand? can u give me that procedure if possible? thanks or your help. by the way...

am i wrong in assuming no spark could be the result of a bad ground? if so tell me so that i can try other things. any ideas as to why no spark?

motor boring and bottom end construction is complete. interesting write up, lot of good inormation. this is wear quality parts and knowledgable machinest are crusial,

to verify the integrity of the ignition systems ground source. or lack their of..... trying to eliminate the posibiities of error or fault in the system.

wear in mass anywear near say... haverhill " merrimack valley area?

to acheive the 3.2 i did a combination of things. bored the block, forged crankshaft, custom forged pistons, and forged rods.... basically alot of boring, a little stroking, custom pistons and rod lengths were the real contributing factors have a really really fantastic machine shop close to...

are you refering to the body ground that goes from " roughly" the exaust side of head, near cyl number 6 to the fire wall? or something else? worked on it again today and could not find the draw..... a first for me. i am stumped, do you think it could have something to do with the cam sensor...

any advice on ems? for my 7mgte. looking for 800 hp whhat seems to work better than others? i was thinking about the motec. is 800 hp obtainable with piggy backs such as safc ect ect. any help from experience would be great

sold ill take one.

i hve built 4 stock or semi stock supras. i say that thi is my first real build because this will be the first one that i actually striped the block for paint, bored it over to 3.2 w forged internals, basicaly the irst time that im going to try and acheive a high hp supra. the other supra...

thanks. basics basics basics. did a draw test from neg bat cable disconected to neg bat terminal. and got power.... now the fun begins trying to locate the draw. any common problem areas? tomorrow i will start the process off elimination " unpluging and checking all components " until i find the...

just installed my 7mgte motor in mk 3 supra 87. 5spd. motor has built internal. c pics. but other wise stock. just wantd to get it runing stock before i put the new turbo, intake ect on. anyways everything is bck together and i have 0 spark. checked to c if ignitor has power and it does but...

sorry im new to these posts, am i doing something wrong? if so tell me what? am not trying to abuse ur thread just inexperienced at this..

Read: http://www.supramania.com/forums/showthread.php?t=50655

goal is 800hp. wil post pics as project progresses. any advice on engine managment? anyone use the motec standalone yet? pics posted in new to supramaniac

just got around to uploading my pics of my 87 upra turbo engine build. looking for about 800 hp any help, info, tricks, and feed back much apretiated