Search results

Ok... I went downstairs to the garage to start to run the wiring, and i had a question. Would the ground wire coming off of the plug for the cig lighter etc. be a white wire with black dashs or something? Theres a 2 red wires, and 2 green wires, and a white and black one. I figured the w/b one...

Oh man thank you a lot JJ! Thats exactly what i was looking for. Ill go ahead and print that out and take it out there with me tomorrow. Thanks again everyone!

I thought the only wire coming off of the cig lighter was the thick red 12v wire that slides over the back of it, but i may be wrong. Its been a few months since i had the center console apart.

Good shit man. Time to go look through cygnusx1. I don't think he has the radio schmatics/cig lighter wiring on there does he? Cig lighter maybe, but i doubt the radio. Do you know what color the ground wire is coming off the deck?

Where should i ground my EBC that im about to install? Im going to use the 12v off the cig lighter for it, but wheres a good spot to ground it at up around the center console etc. If no one responds ill figure it out tomorrow when i go take stuff apart, but i'd be nice to know where a good...

The shutter really sounds like a boost leak to me. That was happening to me a few weeks ago, (Wouldnt boost over 10-11 psi and it would just flutter/bounce back and forth, tested my system with a home made boost leak tester and fixed it. Had numerous random lines that wernt on all the way, a few...

Random noob question, since ive been trolling through this thread, what can happen (at worst) if your radiator is mounted/grounded like his it? You guys are talking about the 2 upper radiator brackets grounding against the frame right?

Did my rear 6" speaker setup like yours, but i didn't do a amp. It actually sounds pretty good for using some cheap 6" speakers and daisy-chaining them off of the other 4" rear speakers. I'd hate to thread-jack but i may get a pic of mine later so you can compare, I used round speakers also...

Haha mine too. My low doesnt work at ALL, but med and high work just fine.

unpainted impo on red.

One last question, where did you run the speaker wire from the 2 you added in? Did you just daisy chain them off the 4" rears that are already in the car? Or did you wire them all the way up to the faceplate.

I really like what you did with the 6x9's in the rear, and i have seen that once before. I actually think im about to do that to my car, how big was that board when you started? Looks something like 2 feet long by 4 feet wide, or however you wanna say it. Anyways, i like it, just why didn't...

glws , good lookin car

Yeah i looked on ebay and couldn't find just that harness piece. One of my friends who has customer accounts with several vendors is going to try and locate me one. HPF also says they have them but everytime i click the link it gives me a invalid page thing. EDIT: Just now i believe the HPF...

hahaha, playstation users WISH it was for ps3.

I didn't know where to really put this thread... But ill just get it out there. I bought a GReddy profec B Spec II Ebc off someone, and it doesn't have the solenoid harness. (The harness that goes from the solenoid to the ebc) Ive been googleing with no good luck on where i could buy one...

Do you know where the vac line for the turbo pressure sensor runs? I installed the boost gauge in that line... so long ago. At least a year and a half ago. But do you know where it runs? Just trying to figure out where the turbo pressure vac line runs... Time to go scan through cygnusx1 for a...

I have a question about the EBC im about to be installing here on saturday. Reading the installation manual it says T the 4mm vac line off the FPR Vacume Line and run it to the EBC (For the built in , but needed , boost gauge). My question is, can i just tee it off somewhere else thats close...

86.5-88 Front Turn Signals with a 89+ Front Bumper? No Thanks Big Ricer Wing? No Thanks Horrible offset-camber'd wheels? No Thanks Ugly Black "Speed Hole" under the trim on the front passenger panel. Big Gap between the hood and front upper Lip. Not my taste.

Ok, since you ran a 57 trim got a question. Did you use any form of boost control? Cause if i run 15 psi, and it spools down low, spooling not creeping, will it continue to creep to 16 18 20 etc.? Also, i didn't have any time for the supra today. Been a busy day.