Search results

  1. OneJArpus

    ECU Location For Motor Swap

    ECU is located behind the glove box. Take that off and it is bolted at the top by the hook. There are "Body plugs" that come off of the engine harness that are plugged into the dash (body) harness to provide the information on the cluster. This is the TSRM (Toyota Service Repair Manual)...
  2. OneJArpus

    1jz Hydro pump or not?

    ^Agree'd, i kept mine and ended up replacing it, it wasn't bad but if you can do it now just get it over with. Its not like you can source out a new pump to keep it functioning properly and if you do its 500+$ Electrical connections (Don't plug them, but don't just cut them and leave them...
  3. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    Pressure and voltage at pump is what he told me to check
  4. OneJArpus

    1JZ map sensor questions.

    i confirmed it this morning. If you have any doubt take a multimeter and put it on the blue & red wire, but the car in the ON position engine off and it will read 5v
  5. OneJArpus

    1JZ map sensor questions.

    I believe if memory serves me correct Ground (brown wire) Signal (yellow/green wire) +5V Reference (blue/red wire)
  6. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    Two of my friends asked if i checked the fuel, how would i check fuel at 5500??!?!?!?!? driving it!?!??!?!!?
  7. OneJArpus

    1JZ Build Plan

    Injectors 550cc minimum! 80% duty max is what you want to get out of injectors, yea you can get 400 on 440's but thats pushing them hard. 61mm turob .68 a/r walbro and AFPR SAFC Wideband Exhaust Manifold 3" Exhaust Thats it. 2-3K Getting deals here and there is very do able. If you have the...
  8. OneJArpus

    1JZ Build Plan

    a 1jz, big single, supporting mods, and a tune
  9. OneJArpus

    Nice pic!

    Green supra my fav Lambo doors or not i'd rock it why? Its not some cheap ass lambo kit its gotta be quality compared to the rest of the car
  10. OneJArpus

    Car stalls when clutch is pushed in once warmed up

    I have a lightweight flywheel and my car has NEVER done that. Did you check for crank walk?
  11. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    Anyone know if the 1zzfe coils will work? Isn't thet 1j/2j 12 tooth crank wheel? Why does it say 18.945 when i look at the wizard? and pickup delay comp: 176.0
  12. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    Anyone running 1zzfe coils on this AEM Unit?
  13. OneJArpus

    SPEC st3 clutch not engaging enough

    Did you check the pedal adjustment
  14. OneJArpus

    Lowest Mileage and Most Expensive MKIII

    Theres an 88 on ebay with 15K miles going for 16K better buy price wise.
  15. OneJArpus

    Aim MXL Strada digital dash/gauge

    ^Yea, they are among the top hottest supra's here lol how do you not know them! lol, those digi dash are hawt! Wish i could get one.
  16. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    I did that and it did nothing =/ It sets the dwell to 2.8 (Dwell VS Bat) dwell vs RPM 100 all the way up to 6400 then it changes to 85 then by 7k its 70
  17. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    My max was set at Dwell Max: 6 Dwell Min: .102 (not sure where to find Coil dwell factor:)
  18. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    I will look into this tomorrow! For some reason my table had the coils step down from 100% to 95 to 85 or soemthing of that nature. What ever was in there on driftmotions base map. I will look and take screen shots of my map tomorrow Anyone have an AEM Map i can take a look at to compare some...
  19. OneJArpus

    Went to the dyno today and got horrible results - AEM V2 PNP 1JZ

    Used the default for coil dwell and it wouldn't go past 4k in idle and does the same driving I adjusted the dwell to 2.0 & i adjusted the dwell to rpm at 4800 to 85 and went down a little but still does the same =/ I'm using OEM used coils right now.