Search results

i hope your not serious on this. lol. i shimmed mine to like 10mm this weekend as i had seen someone say they did 12mm and it was just a tad higherpressure then i wanted it was a bitch to get the nut back on too. i had 4mm before and it made no change i could see on the oil pressure gauge. if...

i pulled a 7mgte at the pick and pull the other weekend and the r154 as it seemed good too. car was bone stock, still had all brackets and stock airbox, paper filter, stock exhaust etc and was wrecked. dont know the miles. cluster was already gone. anyway, checked valve clearance and they were...

itd be the same. how could it be better or worse? all they do is install new pucks. the pucs are bonded and riveted to the disc. ive had several rebuilt by them. never had a problem. place is called Tampa Clutch Supply Inc 5005 North 40th Street, Tampa, FL 33610 phone: (813) 623-1416...

its a good one. if the pucks are worn out local shop here will install new ones for $60. i had them make me a 4 puck. its a "no name". who cares about the name anyway. my 4 puck with stock r154 pp held awesome. also have a 6 puck like yours i used wit ha centerforce pp on a w58. that worked well...

you upgrade anything when rebuilding it? liek the thrust washer and bearing plate? if so lmk how it holds up and i may pay you to upgrade one of my r154's. lol. i just got another 7mgte and if its good im going to throw it in my 84 this weekend with one of the r154;s ive got so i can actually...

http://www.supramania.com/forums/showthread.php?p=954405#post954405 posted pics of the final test piece that has the outside trimmed by the lasercutter as well. group buy ends this month!

http://www.supramania.com/forums/showthread.php?p=954405#post954405 posted pics of the final test piece that has the outside trimmed by the lasercutter as well. group buy ends this month!

http://www.supramania.com/forums/showthread.php?p=954405#post954405 posted pics of the final test piece that has the outside trimmed by the lasercutter as well. group buy ends this month!

http://www.supramania.com/forums/showthread.php?p=954405#post954405 posted pics of the final test piece that has the outside trimmed by the lasercutter as well. group buy ends this month!

cleaned the block good, then rattle can engine primer, then rattle can gray base for the duplicolor metalcast paint, then red duplicolor metalcast from a spray can. just have to prep it good and take your time and it will come out good.

no real updates. ordered the rings and bearings so i can put the bottom end togetherm, havent done it yet though, and also bought a polished 75mm ford 4.6l tb to use when i make my front facing intake manifold. http://www.cardomain.com/ride/2042690/12

bump. group buy ends this month. i ordered another test piece trimmed to the outer diameter of the trans. ill post pics when it comes in so you can see exactly how the units will be shaped.

bump. group buy ends this month. i ordered another test piece trimmed to the outer diameter of the trans. ill post pics when it comes in so you can see exactly how the units will be shaped.

bump. group buy ends this month. i ordered another test piece trimmed to the outer diameter of the trans. ill post pics when it comes in so you can see exactly how the units will be shaped.

go for it. the more people that know the better. i need orders or it wont happen

ive got mine alreayd and im using a t56. but you can use a t5 if you like. once this group buy is done i likely wont get any more unless there is enough interest for another group buy later.

deadline extended http://www.supramania.com/forums/showthread.php?t=62305

deadline extended http://www.supramania.com/forums/showthread.php?t=62305

deadline extended http://www.supramania.com/forums/showthread.php?t=62305

yeah but if it needs a fender, door and hinges makes me wonder if the frame isnt tweaked.