Reign_Maker said:
Yeah fiberglass header wrap...we now have one of the largest inventory of header wrap!!
PM me your address & I will send you some vinyl.
I might sell my soul for Prosport Peak and Hold gauges
- Thread starter Ric
- Start date
Yeah fiberglass header wrap...we now have one of the largest inventory of header wrap!!
PM me your address & I will send you some vinyl.
Holy smokes Glenn, that was from two months ago, lol... You guys take the holidays off? All of them? 
Glenn, whats the word on the widebands?
Glenn, whats the word on the widebands?
Do you need me to talk to the guys in marketing to get them motivated? Because, um, there are QUITE a few guys who are chompin at the bit for these WB's...
I dunno Glenn... There may be people who NEED them more, lol... So whats the hold up? Any news on the delay? We've been holdin out for these for months now... Got ANY teasers?
Hi where can i buy an sensor for the boost gauge
i amusing three gauges butt the boost gauge do not want to read boost anymore and i think the senor is bad baecause al the wiring vacuum source is hooked up
Where i bought the gauges do not answer my emails etc etc
i amusing three gauges butt the boost gauge do not want to read boost anymore and i think the senor is bad baecause al the wiring vacuum source is hooked up
Where i bought the gauges do not answer my emails etc etc
I see the amber/whites will be the first of the clear lens gauges... any idea how far behind those, the green/whites are?
Yeah I couldnt wait on the WB. I bought an innovate. Hate to sink that much money on one but I like the idea of surface mount with the guage.
Also I think my boost gauge my be inaccurate. When I dynoed in November my numbers showed max boost at 10PSI and my guage has never registered that high. Is there anything I can do about that?
Also I think my boost gauge my be inaccurate. When I dynoed in November my numbers showed max boost at 10PSI and my guage has never registered that high. Is there anything I can do about that?
This isn't the first time I've seen people complaining about innacuracy with the Boost gauge. Is this a serious problem? I'll have my Maft-Pro to read boost when dialing in tuning but a very accurate boost gauge I can monitor anytime is still very important to me, and I'm sure I'm not alone.
twincam187 said:
I like my Defi stuff too and was skeptical about prosport in the beginning for a few reasons(I posted in the early pages of this thread). I had never heard of them or anyone using them before and the website was less than nice and that sent a message to me that if the website isn't even up to par, what does that say for their product? But they now have tons of feedback from buyers and the new website is leaps and bounds better than the old one. I have a proport egt and oil pressure right at the moment. Right now the egt is the only one installed along with my Defi BF boost gauge but the prosport is fine and looks fine in white with the Defi.
I'd prefer to use all Defi but it's hard to justify continuing to spend 150-200+ per gauge when the prosports are a fraction of that price. If I had more money to throw around, I wouldn't worry about it and just have all Defis but I have better things to spend money on right now by saving hundreds of dollars over Defi's. The prosports do what I need them to do. They look fine and monitor engine operations.
I still think the Defi's look nicer though, that's for sure. Later on, I plan to change out the prosports for Defis but I'll worry about that after other things are taken care of.
If your boost gauge isn't accurate, make sure it's wired properly (as well as the sender).
I had a problem where I wired them incorrectly and whenever I turned the lights on, the needles would fluctuate and show a reading LOWER than normal.
I had a problem where I wired them incorrectly and whenever I turned the lights on, the needles would fluctuate and show a reading LOWER than normal.
I'll add to Joe's post with the fact that ProSport is a product from the manufacturer of many other name brand gauges. They just brought out their own line instead of being a supplier...
This is why they can afford to be so cheap, there isn't a middle man...
This is why they can afford to be so cheap, there isn't a middle man...