I'm kinda broke right now while i'm working on my swap so could i make the 7mge radiator work for the 1jz? or do i have to get a different radiator and fan? if i do have to get a new radiator which ones do you guys recommend?
Can i make a 7mge stock radiator work for the 1jz?
- Thread starter 86_sports_1jz
- Start date
86_sports_1jz said:
Dunno about making the 7M work but I know DM sells a Koyo Racing rad that is a common swap purchase.
EDIT: http://www.supramania.com/forums/showthread.php?t=24799&highlight=7m+radiator+1jz Just searched, similar question. Instructions on second page for making a 7M rad work w/ fans and all.
The only real difference is that the JZA70 has a thread in the bottom for the temp switch for the hydro fan. They are also about 4mm wider so don't try to swap to tanks like I did, they don't fit!!!!!! Why Toyota changed them that amount I have no idea.
no my buddy is running a stock 7M radiator on his 1JZ with hydro fans it will work except without the temp sensor in the Radiator yur hydro fans (if thats what yur using) will be at full blast at all times.....
if yur using the 2JZ water pump and mechanical fan then it would be the same thing as a 7M with mechanical fan
if yur using the 2JZ water pump and mechanical fan then it would be the same thing as a 7M with mechanical fan
Im using an 87 7M radiator with my 1jz and hydro fan setup with working hydro fan temp sender. I just drilled and tapped a hole in the bottom for the temp sender and used alot of copper High temp RTV on it and it has been working great with NO leaks for 6000 miles now.
The Reaper said:
The fan does not spin at full blast without the temp sensor. It does spin, but that is the slow speed. When the temp sensor is hooked up and the ecu plugged in, that speed of the fan creates a little hurricane. Big difference.
Someone also mentioned on Supraforums that they just used the 7m radiator and just wired a resitor instead of a sensor. ( cut the sensor wire plug and joined the two with a resistor in between.
Drilling and tapping is another good way if it does not leak.
Don't know if this is the right thread for this question but what the heck 
I want to remove the hydro fan setup, what do i have to do? I will beusing a 7M radiator and a 14" electrical fan instead but i'm worried about the hydro fan setup. Do i have to change to a 2jz waterpump, hope not to!
I want to remove the hydro fan setup, what do i have to do? I will beusing a 7M radiator and a 14" electrical fan instead but i'm worried about the hydro fan setup. Do i have to change to a 2jz waterpump, hope not to!
i used a 7M-GE rad on my 7M-GTE set up and it would overheat everytime i drove it. Changed the rad and never had the problem again. So yes, im sure you could use a GE rad, but id bet money on you'll be making another thread asking why your 1J is overheating
w00t told you it would work. and this thread is ANCIENT
this was back before i even ORDERED my 1J hahaha
and tissimo is correct it runs at full speed with out the sensor
this was back before i even ORDERED my 1J hahaha
and tissimo is correct it runs at full speed with out the sensor
RWHP;921878 said:Ooh my bad, didnt see that this was about the GE rad, i have the GTE rad
You may have to change over to the MkIV H20 housing and pump setup.YOu wouldn't need a fan if you are using the electric ones.
If you are in the us, I will take your hydro fan / shroud setup
tissimo;921885 said:
Dang these little things are so inconsistant.
Here's how I tested mine on the 2JZ :
NO Senor, no ECU = Slow speed.
NO Sensor , ecu plugged in = Full speed
ECU + Sensor both plugged =l normal desired operation > Fan speed varies according to temperature.
you are correct. don't be so hard on yourself.
we are talking about with the ECU and no sensor. so your chart is right on target!
we are talking about with the ECU and no sensor. so your chart is right on target!
Hey guys, would it be alright just to run a 7mgte rad and 2jz fan by them selfs? without the little stock fans next to the battery?
suprastanger507mgte;922660 said:You may have to change over to the MkIV H20 housing and pump setup.YOu wouldn't need a fan if you are using the electric ones.
If you are in the us, I will take your hydro fan / shroud setup
Okay, so 2JZ waterpump it is with a 14" Summit fan
Noo sorry, i live in sweden!