Search results

What is the voltage reading when the lights are not on? Where did you buy the alternator? I have gotten 3 DOAs in a row from autozone in the past, then 2 from pepboys, then finally a good one from toyota. Since bumps seem to affect the problem have you checked simple things like cleaning the...

It's a hit and miss with the snapon rep too... I have one ten minutes from my house that I can call whenever and he will repair/replace right out of his house. I only use snapon for ratchets though, so the truck is guaranteed to have some in stock. When it comes to sockets, I saw a kobalt 14mm...

All my ratchets are snapon, after you go dual 80 you can't go back lol... everything else is mostly craftsman

Here is my old setup... i had the maft pro screwed in where it sits in the picture, and a cover to hide the wires (not pictured)

One of my cars had a headgasket done before I had gotten it, instead of checking the head for warpage the machine shop had simply decked it so it had a flat surface but was warped, which warped the cams. I ended up replacing the entire head. What do the cam journals look like? Are the cams...

I'm with you and agree with you, but for arguments sake, is it possible for Iraq's economy to grow exponentially when oil is tapped, and is being sold properly? Would this take too long?

lol, I'd rather take my money and waste it in vegas... but I want to formulate good arguments against people doing it, and cannot find anything to back up my feelings stated above.

Recently someone told me that the best investment I can make is to purchase 1000 US dollars worth of Iraqi dinars, and wait for them to be revalued, at which point they will be worth almost as much as the USD, multiplying my initial 1000 by 1000 when I sold my newly revalued dinars. I have...

I haven't installed anything to lock it into gears, I think I'll just stay out of boost until I'm 5 speed.

All my cars usually have a name, my two supras I usually refer to as poopra just because it is fun to say. I like to give personalities to the supras as they seem to have them. My supra recently decided it needed a metal headgasket, so it blew it's old one, then it decided that instead of...

What would your fix be? Those sensors do not exist anymore, and this prevents codes from occurring because of their absence... What do you propose to fix the issue?

Any Ideas?

Both codes 24 and 31 are from the AFM, make sure it's plugged in properly Code 52 is a knock sensor problem, the wires going to the knock sensors fail, or they could be damaged. Knock sensors are under the intake take a peak and see if there are any hanging wires.

I found top dead center before I had the timing belt on so the cams were freely adjustable, they are both set with the timing marks on the gears lined up with the timing marks on the cover behind them

Courtesy CRE:

I have been trying to tune my car well with my maft pro and have run into an issue. When I first floor it, the tranny downshifts and the turbo spools to 1 bar. For about 3 seconds it runs at about (13-14ish I know this is very lean for boost) then it goes to the 11 ratio I am looking for. I...

Put both cams with timing marks lined up Took out spark plug #1, checked for TDC, found it Installed timing belt Installed CPS with timing marks lined up ---------- Post added 04-10-2010 at 12:11 AM ---------- Previous post was 04-09-2010 at 11:56 PM ---------- Thanks for the advice...

I set my timing to 12degrees my mods: 550cc injectors, all supporting mods maft pro 60-1 trim ct26 7mge cams So I time it (TDC set properly, CPS installed properly) to 12 degrees and have no power, check my exhaust manifold and it is red, so I think timing is retarded. Set my...

Sorry, totally forgot to mention that it does not start when using starting fluid. My G1 pickup is not working, I have spark, but if one pickup was not working would spark timing be off? BTW: I'm putting the following because it took me a bit of time to find them, and I want it to be easier...

If anyone has a spare working CPS I need one tonight, please PM me if you have one, and we can work it out through that. Thanks to any replies, if anyone knows others with parts please let me know