Search results

  1. OneJArpus

    For those with a 1.5JZ using GE Parts

    1. I am running a boost logic 2.5 MM headgasket. The head was machined all i forgot my calculations but it wasn't too far off from what i had on the head n block etc etc.... As rakkasan stated please do you own calculations but as a "helper i ran 2.5mm" 2. TT oil pump MUST be used as it has the...
  2. OneJArpus

    1jz running lean in boost

    Do you have the stock fuel damper? 12v mod, is it normal to see 12.x? I see 13.x (what ever my alternator is charging at). Shouldn't it be a little higher? When does the misfire happen? Full throttle? Partial? In boost? Going into boost? Cruise? Low RPM? High RPM? Does it happen in neutral?
  3. OneJArpus

    GM 3bar Map Sensor Question

    ok Here is my dilema, Some people say O 1jz here i got the gm 3 bar to work with my setup on stock ecu but no one is specific on HOW they got it to work Stock MAP Sensor Readings & Settings on SAFC What i see when I turn the car on monitor with stock MAP Sensor Type for Stock MAP Sensor...
  4. OneJArpus

    what killed your last motor thread

    1JZGTE - Dented coil pan which didn't look bad from shipping and me for not double checking it.... =/
  5. OneJArpus

    My Targa Roof is no more... Need advice.

    Might be your time to upgrade @ the same time http://cgi.ebay.com/ebaymotors/86-92-Toyota-Supra-Mark-III-CARBON-FIBER-TARGA-TOP-_W0QQcmdZViewItemQQhashZitem2a0b36c6cfQQitemZ180576765647QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories#ht_500wt_1182
  6. OneJArpus

    Groudn Clearance question

    I run MKIV TT wheels, TEIN SS Coilovers dropped 2+inches. I clear just about everything but do scrap my resonator but my exhaust hangs a little low. Once tucked i think i'll have no issues, small speed bumps and driveways it goes up pretty easy
  7. OneJArpus

    Water in rear hatch

    toyotapartscheap.com driftmotion.com or Champion Toyota / Elmhurst on the other site SF I got a new hatch seal IIRC i paid 68/86 from dealer a few months ago. Tail lights are cheap. Also, take off the bottom rear window molding, apply silicone on the studs of the molding as water gets under...
  8. OneJArpus

    DM oil sender hose

    ok. Wasn't sure as the 7M sensor went right into a 1/8 NPT hole and thats what the adapter line is on DM. BSP to NPT... =/ Why not BSP to BSP?
  9. OneJArpus

    935 Motorsports/1jz harness

    if you paid with a CC contact your CC company dispute it. Try disputing it through paypal as well ify ou did it that way. If you sent a money order, consider it a huge loss and look to get it back somehow but i doubt you'll get anything... Cash? Ha its over.. Wire Xfer? Same
  10. OneJArpus

    DM oil sender hose

    IIRC 7M = NPT as the sensor on the 7M is a NPT 1JZ & 2JZ uses BPT.
  11. OneJArpus

    That stupid sputtering problem is back!

    ^LOL... was it cooler that day when it drove better? The coils heat up if it was cooler then the cooler air prevented the coils from getting extra hot. It "could" be the coil but!!!! I hav eno clue i have the same issue and i have a new coil and recapped ecu, i've tried different ECU, MAP, and...
  12. OneJArpus

    Dropping the oil pan??

    scratch that... saw u just finished it LOL
  13. OneJArpus

    Fitting Work Equip wheels with a big brake kit

    i don't see why they won't work.
  14. OneJArpus

    ***The Burgandy Supras Thread***

    Two year update since my last post!