Rebuild 7M power

[fstsupra]

I would love to applogize but i refuse as we only had 4500 dollars and only about 3k of that went into the car, basicaly we didnt get near the funds that we were suppose to. So with that in mind i would love to say no appolgies here however i would like to say 7000 bucks for 700 with a bit more supra experiance is more possible now then before retail is for Newbies anyway Just thought i would defend my honor ! talk to you guys later jugalo65978 admitted defeat not acknowleging that we had under half the budget Some day when i get 7-8k laying around ill do it Mean while im going with 1jz swap.

 

[jugalo65978]

I ordered my barings and some ARP rod bolts. :biglaugh: im realy exited to get this car on the road. it seams like it takes for ever, so sad. ill put up pics when they get here.

 

[jugalo65978]

here are pics of my freshley painted block

 

[jugalo65978]

ARP rod bolts

 

[jugalo65978]

i also got a Q45 throtle body for free:naughty: im gona try and make a ffim for the throttle body hopefuly it turns out ok.

 

[jugalo65978]

im geting my internials back from the machine shop to marrow:icon_bigg i am so exited ill put up pics this week end. i got my rods shot peined and all my intearnials balanced and my crank milled. ill be putting it all back to gether soon. this is soo cool!

 

[jugalo65978]

i got my rods and pistons installed here are some pics

 

[jugalo65978]

just got my block plastigaged that was a pain in the ass! im going to have to get my barings oversized 6/1000 of an inch.:3d_frown:

 

[Figit090]

how can faulty injectors spray fuel into the oil? does it squeese past the cylinder on a non-compression stroke and get in the oil?

 

[pimptrizkit]

how can faulty injectors spray fuel into the oil? does it squeese past the cylinder on a non-compression stroke and get in the oil?

fuel is as thin as water when you talk about viscosity,. the rings are designed to scrap a thicker viscosity off the cylinder wall. the gas soaked cylinder cant keep the gas in, and almost drains instantly on it's own.

on a side note, i hope your machinest either re-sized your rod's for the arp bolts or carefully pressed them in and out.

best of luck!

 

[jugalo65978]

yep i got the rods reshaped

 

[SevenMKIII]

How much was it to reshape your rods? I've been trying to source new stock rod bolts from Toyota and everyone is telling me they have to piece together a whole set. (Didn't mean to threadjack)

-Chris

 

[pimptrizkit]

idk i think it was around 75 for all six,.. tho i had other work done to mine at the time so it was more around the 300 mark for me..

 

[IJ.]

Resized maybe?

 

[jugalo65978]

shotpein, reshape, and ARP rod bolts was around $150.

 

[IJ.]

shotpeen, resize, and ARP rod bolts was around $150.

Fixed....

 

[Idealsupra]

i hope to god your engine building skills are better then your spelling and grammar. for YOUR sake

good luck!

 

[jugalo65978]

i hope to god your engine building skills are better then your spelling and grammar. for YOUR sake

good luck!

you bring up a good point, good thing building an engine dose not require any sort of spelling skills.:naughty:

 

[CzA]

"i hope to god your engine building skills are better then your spelling and grammar. for YOUR sake"

Is it not supposed than not "then"?

just breaking balls

I take it prices are in us dollars?

 

[jugalo65978]

yep us dollars

"i hope to god your engine building skills are better then your spelling and grammar. for YOUR sake"

Is it not supposed than not "then"?

just breaking balls

I take it prices are in us dollars?

yep us dollars