November Mini Meet

VanSupra

Supramania Contributor
Mar 31, 2005
803
0
0
Van,B.C.
Well, due to popular demand and requests from our die hard Supra fans on the wet coast, Sunday Nov 19th/06 1:00PM Red Robin Guilford. I hope to be up and running by then aswell so, "Be there or beware"

:naughty:
 

GrimJack

Administrator
Dec 31, 1969
12,377
3
38
57
Richmond, BC, Canada
idriders.com
xXxICExXx said:
What stage is it at?
Lets see here... I need to:
- check valve clearances
- install valve covers
- pull engine off stand
- install rear oil seal
- install oilpan
- install flywheel & clutch
- install tranny
- drop engine and tranny into car
- install driveshaft
- hook up power steering, AC, alternator
- tighten crank pulley
- install belts
- install radiator
- install radiator fans
- remove IC, clean, reinstall
- install IC piping
- install plug wires and coilpacks
- connect all wiring
- install MAFT Pro, including MAP sensor, wideband, IAT sensor, boost control solenoid
- install driveshaft
- install shifter
- reassemble dash
- charge battery
- install battery
- tune
- ENJOY :D
 

xXxICExXx

New Member
Aug 6, 2006
366
0
0
40
Abbotsford, BC, Canada
GrimJack said:
Lets see here... I need to:
- check valve clearances
- install valve covers
- pull engine off stand
- install rear oil seal
- install oilpan
- install flywheel & clutch
- install tranny
- drop engine and tranny into car
- install driveshaft
- hook up power steering, AC, alternator
- tighten crank pulley
- install belts
- install radiator
- install radiator fans
- remove IC, clean, reinstall
- install IC piping
- install plug wires and coilpacks
- connect all wiring
- install MAFT Pro, including MAP sensor, wideband, IAT sensor, boost control solenoid
- install driveshaft
- install shifter
- reassemble dash
- charge battery
- install battery
- tune
- ENJOY :D


Maybe you will make the january mini meet :icon_razz
 

BTZ

New Member
Apr 5, 2005
103
0
0
87
Burnaby
GrimJack said:
Lets see here... I need to:
- check valve clearances
- install valve covers
- pull engine off stand
- install rear oil seal
- install oilpan
- install flywheel & clutch
- install tranny
- drop engine and tranny into car
- install driveshaft
- hook up power steering, AC, alternator
- tighten crank pulley
- install belts
- install radiator
- install radiator fans
- remove IC, clean, reinstall
- install IC piping
- install plug wires and coilpacks
- connect all wiring
- install MAFT Pro, including MAP sensor, wideband, IAT sensor, boost control solenoid
- install driveshaft
- install shifter
- reassemble dash
- charge battery
- install battery
- tune
- ENJOY :D

lol, install 2 driveshafts, lol.
ill be there...
 

NashMan

WTF did he just wright ?
Aug 5, 2005
4,940
17
38
43
Victoria BC
how you break damper ??? did yae just chip it or some thing

mine has chip in it i really shoudl replace it but i really thinking on getting one


oh yae if you don't have puller 2 flat blade screw driver and wiggly the shit out fo it if not use puller if that don't work i wan tot see you r car done secound time befor mine even run's


run's away crying
 

GrimJack

Administrator
Dec 31, 1969
12,377
3
38
57
Richmond, BC, Canada
idriders.com
I have a puller.

There was a small dent in it, so I tried to tap that out with a hammer, and a sizeable chunk of the damn thing just popped off. :(

I'm concerned that if I left it like this, it would eat belts.