dyno day ct-26!!!

[quake]

just put the sup on the dyno mods include .20 overbore wiseco all arp cometic gasket 550cc injectors vpc no afc yet full turbo back 3" precision front mount blitz blow off greddy ebc air fuel went sub 10s after 5600rpm so more tuning needed before that rock steady 11:1 end result 325whp and 394tq at the wheels! now we put the 67 back on :icon_bigg peak boost 18psi holding 15psi

 

[starscream5000]

Wait? What?

 

[Piratetip]

Thats one long breath.

 

[starscream5000]

Just put the supra on the dyno. Modifications include: .020" overbore wiseco pistons, all arp hardware, cometic gasket, 550cc injectors, HKS vpc, no afc yet, full turbo back 3" exhaust, precision front mount intercooler, blitz blow off valve, greddy ebc. Air fuel ratio went sub 10s after 5600 rpm, so more tuning needed before that rock steady 11:1 A/F. End result.........325whp and 394tq at the wheels! Now we put the 67 back on :icon_bigg peak boost 18psi holding 15psi

Fixed it some

 

[quake]

Wait? What?

i know was not expecting 396 with a stock ct lol

 

[MassSupra89]

I think that was directed more at how hard your sentence was to read. Comma's and Periods make it much easier to understand.

Very good numbers though, I would not expect that torque on a stock CT either, not an upgrade?

 

[starscream5000]

Where's the torque at though? That's what's counts.

 

[quake]

I think that was directed more at how hard your sentence was to read. Comma's and Periods make it much easier to understand.

Very good numbers though, I would not expect that torque on a stock CT either, not an upgrade?

Hey it was a fast post. As for torque it was at 3800rpm.

 

[starscream5000]

I bet it dies off pretty bad up top though doesn't it? The CT's torque looks good on paper, but I'd rather have my torque peak about 1-1.5K higher, that's just me though...

 

[quake]

I bet it dies off pretty bad up top though doesn't it? The CT's torque looks good on paper, but I'd rather have my torque peak about 1-1.5K higher, that's just me though...

actually its a steady drop. Not too bad, down to down to 300 at 5800 when the fuel goes below 10:1. still has 350ft lbs at 4800.

 

[starscream5000]

I guess that's due to your boost spike though right?

 

[quake]

I guess that's due to your boost spike though right?

thats what im thinking, but i only went to make sure it was running rich enough

 

[IwantMKIII]

impressive numbers...what boost were you at??

 

[quake]

impressive numbers...what boost were you at??

peak 18psi dropping to 14.5

 

[IwantMKIII]

^^oh...i misread...damn! thats a lot for the little ct-26 unmodified...be careful

 

[quake]

^^oh...i misread...damn! thats a lot for the little ct-26 unmodified...be careful

not going to keep it in i have a 67mm

 

[quake]

update: dynoed on last friday and made 407rwtq and 350rwhp will post dyno sheet tomorrow. Also ran 13.7 at 105mph will see about posting vid this was on 18" rims. selling this turbo now as my new one is on the way make an offer

 

[White Zombie]

Impressive numbers man. Sounds about whrere I will be at in a few months.

 

[quake]

thanks

 

[Poodles]

CT = torque monster

the only thing better than a stock CT at spool and torque is very expensive...