Connect AVCR ?

[ptauss]

Greeting ,

I bought Apexi AVC-R of bargain and unfortunately for me , it’s that I miss harness wiring for the connection of the various elements (solenoïd and pressure sensor) , I have just the cable of the Controller with his connector female and 10 cm wire cut with the connector male . To refer to the diagram of page 52 of « Instruction manual » , it misses to me the harness of 12P which goes until to connections of 3P (pressure sensor) and 2P (solenoïd) .

I drew from the wires which replace the wiring of origin but my problem is that I don’t know where to connect them on the Controller .

I connected these wires :

1. Red ----> power
2. Purple ----> RPM
3. Green ----> ground
4. Black ----> ground
5. Gray ----> throttle
6. White ----> speed signal

Which are the wires to connect the solenoïd ?
Which are the wires to connect the pressure sensor ?

Could a charitable heart give me the solution to my problem ?

Thank you.

ptauss

 

[IJ.]

Do you need the AVC-R end of the wiring diagram or the other end?

 

[gt4]

the small gauge pink goes to the solenoids pink and the small gauge red goes to the solenoid black.

 

[ptauss]

Do you need the AVC-R end of the wiring diagram or the other end?

Hello ,

I have only 10 cm wires cut after the 2 connectors of the controller .

I want to know where the solenoïd and the sensor pressure connect , about which wires we connects them .

Thank you .

ptauss

 

[IJ.]

Here ya go this should make it a little easier!

There is a section in there showing the wiring harness and connections!

Scroll down to bottom, click free, follow instructions

http://rapidshare.de/files/19029027/Apexi_AVC-R_Manual.pdf.html

<Thanks Whiplash)

 

[ptauss]

the small gauge pink goes to the solenoids pink and the small gauge red goes to the solenoid black.

Hello ,

I made this connection but when I switch on , the solenoïd pull and release continuously !

Can you say to me how connected you your AVC-R ?

Thank you .

ptauss

 

[ptauss]

Here ya go this should make it a little easier!

There is a section in there showing the wiring harness and connections!

Scroll down to bottom, click free, follow instructions

http://rapidshare.de/files/19029027/Apexi_AVC-R_Manual.pdf.html

<Thanks Whiplash)

Thank you for the file but I already saw it .

To refer to the diagram of page 52 , it misses to me the harness of 12P which goes until to connections of 3P (pressure sensor) and 2P (solenoïd) .

ptauss

 

[ptauss]

There is nobody who can tell me which wires to connect my solenoïd and pressure sensor !!!

However , while reading in this forum , I note that there are many users of this controller .

Please , help me , I need these infos to finally be able to use this fabulous controller .

Thank you .

ptauss

 

[IHI-RHC7]

I can check later, I'll have to look at the connections to tell you which ones go where...

 

[ptauss]

Ok , thank you IHI-RHC7 to interest you on my problem .

I hope to be able to solve my problem with your assistance .

I will await your answer .

THX

@+

 

[ptauss]

I can check later, I'll have to look at the connections to tell you which ones go where...

I will await always your answer .

Here it following my tests,

I connected the solenoid with the wire red (the same one as that of the power) and the wire pink.

For the adjustments of the AVC-R , I put in “SENSOR SEL”, the option “Absolute1” , because with the option “Relative1 or 2” , the solenoid plays of the castanets when I turn on and I turn off the engine .

This phenomene , which is very unpleasant , is normal ?

It is what the difference between these 2 options: relative and absolute ?

After my 1st tests on road , I note that I finally passed the bar of the 7 PSI. :yelrotflm

Thank you with those which they want to inform me well.

@+