Cams
- Thread starter corylee316
- Start date
*ahem* who won the ashes? Oh yes, thats right, us 
Fuel is going down here - down to 82p a litre now - thats a drop of 16p per litre since September
Sun? Overrated in my opinion!
Fuel is going down here - down to 82p a litre now - thats a drop of 16p per litre since September
Sun? Overrated in my opinion!
you can alot of cam shops will add mealt to the cam shaft aka welding that is whatv was done time mine so i don't have to deal with all that bs
ps i know they will ware out fast but who care's teh 7m will blow befor they ware out
ps i know they will ware out fast but who care's teh 7m will blow befor they ware out
www.deltacam.com (around $90 ea ground to your specs. I think most guys get a 272 cut and push a wet spray system)
Your best bet, aside from a pair of cams, is raising the compression with domed pistons, a good port n polish(and valve job), and aftermarket engine management. I've seen plenty of guys use high compression pistons with a good tune. Their n/a's ran like a cheeta on cocaine
Your best bet, aside from a pair of cams, is raising the compression with domed pistons, a good port n polish(and valve job), and aftermarket engine management. I've seen plenty of guys use high compression pistons with a good tune. Their n/a's ran like a cheeta on cocaine
I tried e-mailing them with the e-mail address that is on their web site and I got a mail delivery problem. I tried two different e-mails(work and home) and got the same thing. They sound like they might be part of a solution for power NA style.
They are in Tacoma. I will have to call. They don't like me doing that during work for some stupid reason. I tried again. For all I know it's our server here at work. It fiters out anything that resembles fun.
I think 272 is abit extreme for your average, daily driven N/A. What # would be good for a more mild setup? I might look into this if it's only $200 for both regrinded.
-Matt
-Matt
If these guys are decent at what they do they should be able to figure out what will work well with the mods you have and what you have planned. I have a buddy that has one of those computer programs that you can adjust the cam specs, compression ratio, ect. and get at the flywheel guesstamate of what you should expect. I'm not to sure how accurate that it is, but I don't trust computers that much.
Yeah, I wonder what a mild # would be, this website here can regrind your cams to either 244 or 230 degrees, the 244 is the more extreme, but I'd say that'd be a good goal to go for. Look @ the bottom of this link where it shows the 7M.
http://www.webcamshafts.com/pages/toyota-auto.html
http://www.webcamshafts.com/pages/toyota-auto.html
Those are rewelded. They add material and then grind it away. I don't have any expreiance with those. I'm sure someone will chime in on that. The other ones seem to be new grinds made from cam blanks. They seem to be better DD cams though.
**My e-mails did get through to them. I think my computer has some defects(maybe the opperator). Their number is 1-800-562-5500.**
**My e-mails did get through to them. I think my computer has some defects(maybe the opperator). Their number is 1-800-562-5500.**
Last edited:
The Brian Crower kits are for both 7M's and are pretty reasonably priced, for the entire 272 kit its like $600, thats not bad considering your getting brand new cams. They also have other profiles, check out there website at briancrower.com!!!
anyone have the specs for the NA cams, i pulled the numbers off of the Brian crower website for the 264s
264°/264° 220°/226° .336"/.332" 8.53/8.43
264°/264° 220°/226° .336"/.332" 8.53/8.43
My buddy has been running a set of delta regrinds in his b18 Hon-Duh. Has roughly 10K miles on them and still in good condition.
Give them a call they can give you more options, I said 272 as that's a common grind for someone looking in to spraying their motor
If u can get the new cams, that's great too. It's x-mas time so a majority of my cash went in to presents lol
Give them a call they can give you more options, I said 272 as that's a common grind for someone looking in to spraying their motor
If u can get the new cams, that's great too. It's x-mas time so a majority of my cash went in to presents lol