Search results

If you can, please sticky this webpage for future reference. It is a complete how to on taking apart your 1JZ and can be used for a 2JZ as well since both engine are highly similar. It was posted on MKIIITech but it would be nice if that whole posted could be backed up on SupraMania's Server...

You have to be kidding me. I would have killed someone to get a chance at my fifth Grade teacher. She was super hot and had an ass for the ages. My chemistry teacher in High School too, she had a nice rack and her nipples were always showing. Then this Kindergarden teacher too, she was...

I am rebuilding my R154 because a "rebuilder" said he could do my gearbox and started then after he say it, never came back to our shop to finish it. So, now I have a gearbox half apart and doing it myself. I watched when he took it apart so I know some stuff. I pressed in new bearings and...

Ok, so I am building my engine and I need some advice on gauges. I have used the ProSport Premium Peak/Warning gauges before and they were fine, just seemed cheaply made but were accurate when compared to the standalone, so I am not sure if I should go with them again. I am looking to get...

So I picked up this 88 Light Blue Front Clip Swapped 1JZ With A Set Of Volks, 89 conversion except the front bumper and cluster with and the cleanest stock interior I have seen. Interior is blue as well. The car also had a 3in exhaust with a flowmaster muffler. I drove down to Fairfax...

Standalone: LT12s Engine: 2JZ I went into my standalone and saw that the TPS reading was at 99 percent. Does this mean that it is not wired in properly or the Microtech does not support it. I know it does not support the stock stepper motor but it is idling without stalling out. How are...

I have a 7M that I rebuilt and now I am trying to start it. We changed to a T4 67 trim setup and still using the stock AFM. I am trying to start the car and it gets spark and fuel. My problem is when trying to start the car, it will shortly rev to about 600 RPM and then stall. I checked...

Hey guys, I just got a load of parts on a deal right this minute and saw a HKS In-Tank Fuel Pump. It has a part number as well but I cannot find it on HKS' website. It has a similar design to a Walbro as long as the wiring connections are concerned. What do you guys think about it, anyone...

I am on the highway driving and then go to exit. The exit is in the process of doing a turn and it is a pretty wide turn. I am in the exit lane and this taxi in the lane next to me, turns wide and swipes my car. I was in my daily driver at the time. He tried to blame it on me that I tried...

Hey guys, I currently have three Supras, an 87, 89 and 91. I am building the 89 and I bought the 91 since the guy took apart the engine and forgot how to put it back together. I went inside it the other day and I believe I dropped the key inside or left it by the strut tower under the hood...

What is the part number for the 89 round mounts? The TSRM has the same part number for both round and square mounts. Thanks.

Where can I find a gauge pod? I can't find one for my 1989 Supra at Auto Zone or PepBoys. I know about the universal ones but the ones that are there are too wide. Where did you guys get yours from? I say that SupraSport.com has a gauge pod but their shipping is bad because I ordered from...

The problem is that my car will idle at 450RPM and will have an intermediate miss. Things I Have Tried: Checked Timing - Set to 10 Degrees Check Codes -None Vacuum Leaks, None, Vacuum is at 21. My throttle body was painted and it did not return back normally, so I have to change it. Upon...

How do I hook up electric fans? I have looked around for a write up on how to do this. I know I can use a fan controller with a probe in the radiator but what about a thermostatic switch in the thermostat housing since I am not using the Bimetallic valve. I do have the upgraded alternator...

Hey guys, I am running a T4 turbo setup and I want to cool my engine day down to the lowest I can. I have wrapped everything I can in Thermo-Tec heatwrap and plan to cover all hoses with heat protective sleeves Now, I am looking for an Oil Cooler Kit but have had no luck. What are you guys...

Hey guys, my theme is black and red on my car, red being the body color. Now I am looking for a set of black rims with a polished lip. I checked the build threads but can't find any. I like Ron R's Supra's rims but I am not sure if they are offered in black. Staggered will be nice as well...

Hey guys, I installed my DriftMotion turbo kit that David had put together for me when he worked there. The down pipe that shipped with the kit does not have a flange to mount the stock O2 sensor. It does have to screw in bungs that I can use, one for the stock O2 sensor and the other is for...

Hey guys, does anyone have a basemap for the 7MGTE with the MAP sensor setup? Anyone know a way on how to eliminate the IAC? I have seen it done with a standalone, just I have no idea how. Thanks, Andy. PS - The AEM interface is very easy to use if anyone is wondering about getting one.

Hey guys I placed a order on Saturday night with SupraSport and I got the confirmation E-Mail and I have not heard anything since then. I tried calling but the number comes up with "The Subscriber You Are Trying To Reach Is Unavailable." Any Ideas?

Hey guys, I bought a turbo kit from DriftMotion and I don;t like the return line for the turbo since it has so many AN fittings. I saw on the forums a guy who had a stainless steel line with two fittings, one for the turbo and for the block. Does anyone know where I can find a one piece like that?