What kind of IC are you guys running?

[Datsrboi]

Im in search of some aftermarket intercooler since I am redoing my car that I might as well upgrade it. The original owner brought some MaxXacessory? brand company but never completed the crap. It has all the piping but is missing the intercooler.. Since My setup is basicly an intercooler what will have an In and Out on opposite side, I figure I get a nice one.

What type of intercooler are you guys running and whats the IC size? Also say if you had to removed or modify your impact bar? And if you have pictures that be soo cool too.

My setup so far is Maxxaccessory IC pipe with no intercooler :nono:
I might be going after those ebay intercooler with 31X12X3 with 3 inch in and outlets and I wont be modifying my impact bar.

 

[IJ.]

31/24 x 12 x 4" Chinese Bar and Plate here.

 

[starscream5000]

Bigger spearco style IC here.

 

[viper92086]

spearco style

 

[TurboWarrior]

spearco style

 

[mhopemk3]

Larger Spearco style as well.

 

[Wills7MGTE]

Spearco style, excellent intercooler and uses stock piping routes which is nice because I have custome hardpipes I had made based on stock route.

 

[Dominus1222]

You guys running the larger style spearco, where did you relocate your oil cooler? I'm planning on going this route and wanted to know what you guys had done.

 

[mhopemk3]

I tucked mine right next to the intercooler. It fit perfect. I had to replace the oil cooler lines due to them being too short.

 

[89turbotoy]

now i'm running a hahn racing intercooler bu as soon as it gets here will be running a larger spearco replica

 

[Datsrboi]

You guys are lucky.. I have that MaxAutoworks piping that has it route to the in and out on separate sides. That dam site shut down.

 

[supra_ed]

i have the horsepower freaks(ets) kit- spearco core.

ij: can u fit a 4in core inside the stock bumper? or did u trim that bumper seam?

 

[upgradedsupra]

30x14x4 and a vendor from here .. Extreme Turbo Systems VERY good quality. :icon_bigg

Duane

 

[suprarich]

Greddy/Trust mk3 turbo specific kit here. Had to relocate the oil cooler.

 

[IJ.]

i have the horsepower freaks(ets) kit- spearco core.

ij: can u fit a 4in core inside the stock bumper? or did u trim that bumper seam?

Ed: I trimmed mine A LOT

But it will squeeze in there.

 

[tte]

Bigger spearco style intercooler. Could barely squeeze it in between the front bumper supports.

I located my bigger oil cooler at the drivers side foglight position. Removed the fog light. I have yet to build a duct that attaches to the fog light hole and out to the entire cooler core to route all the air to the cooler.

Cheers,
Roy

 

[Datsrboi]

Darn no one else have the Maxautoworks setup?

4inch think drool. Mine will only be 3 inch. I am trying to advoid triming the bumper nor the impact bar down.

 

[Mr. Y]

Spearco style is crap (if it hasn't flow divider inside) for high boost application.

 

[starscream5000]

I have no flow divider in mine, but it's the larger version though.... :dunno:

I still have my stock oil cooler in for the time being, but I unbolted it and moved it straight back towards the radiator and on an existing bolt/hole.

 

[TurboWarrior]

Are these spearco style IC's tube and fin? I can't remember