Welcome to my build thread to start this off im going to restore this 91 MA70 hardtop mk3 supra to running condition ASAP!
I really dont know too much about its past, but this is, what it is xD
Just did a Bearing Install!
LOLL xDDD
Anywho!, i have not taken many photos of the build as its been progressing. so this is where im going to start.
doing a 2jzgte swap to this 91 + R154
)
Here is some progress of the swap!
Getting Head Ready For Machine Shop!
Bottem End Ready for Machine Shop!
My Crank
Some little stuff i did on the side lol, and Yes Super Moniter will be wired in and will work!
I Loveee Carrillo!!!DD
One of the best brands on Con Rods/Pistons I know!!
As of 5/16/2012
Today, It Starts!!!
I Took photos etc,.
Rear Suspension on, aka KYB Struts/Eiabach Prokit, new pads, 4.10 LSD
and some tear down xD (I should of took pics when installing rear/etc but will for now on!)
UPDATE 5/16/2012 to 5/17/2012
Got ALOT Done! lol.
Windshield Removed!
Sound Det~ IS ALMOST GONE!!DDDD
All i have to use is a Hammer and Screw Driver,. Only took me about 2 hours to get this far with it. xD
Went to Ollies Store to buy a tarp and noticed the fast and furious section LOL, had to look/laugh
Than Noticed This
Every Single One!, Broken!
(NOTE: I DID NOT DO THIS SO PLEASE DONT ASSUME)
and out comes my oil pan setup
(1jzgte is for sale, comes with front sump pan, longblock, running, 650.00 pick up only must contact me via PM in reguards to this, due to this is not a for sale thread)
got bored and started to remove all 1jzgte head components (not the 1jz head shown above)
Had to finish early though, only got the intake side done
(Will have a update tonight late, or tomorrow morning around this time
This Thread Will Be updated Daily!
(Sorry if about Grammer xD)
I really dont know too much about its past, but this is, what it is xD
Just did a Bearing Install!
LOLL xDDD
Anywho!, i have not taken many photos of the build as its been progressing. so this is where im going to start.
doing a 2jzgte swap to this 91 + R154
)Here is some progress of the swap!
Getting Head Ready For Machine Shop!
Bottem End Ready for Machine Shop!
My Crank
Some little stuff i did on the side lol, and Yes Super Moniter will be wired in and will work!
I Loveee Carrillo!!!
DD
One of the best brands on Con Rods/Pistons I know!!
As of 5/16/2012
Today, It Starts!!!
I Took photos etc,.
Rear Suspension on, aka KYB Struts/Eiabach Prokit, new pads, 4.10 LSD
and some tear down xD (I should of took pics when installing rear/etc but will for now on!
)
UPDATE 5/16/2012 to 5/17/2012
Got ALOT Done! lol.
Windshield Removed!
Sound Det~ IS ALMOST GONE!!
DDDD
All i have to use is a Hammer and Screw Driver,. Only took me about 2 hours to get this far with it. xD
Went to Ollies Store to buy a tarp and noticed the fast and furious section LOL, had to look/laugh
Than Noticed This
Every Single One!, Broken!
(NOTE: I DID NOT DO THIS SO PLEASE DONT ASSUME)
and out comes my oil pan setup
(1jzgte is for sale, comes with front sump pan, longblock, running, 650.00 pick up only must contact me via PM in reguards to this, due to this is not a for sale thread)
got bored and started to remove all 1jzgte head components (not the 1jz head shown above)
Had to finish early though, only got the intake side done
(Will have a update tonight late, or tomorrow morning around this time
This Thread Will Be updated Daily!
(Sorry if about Grammer xD)
Last edited:
